#Wall mounty bit set install
#Wall mounty bit set plus
#Wall mounty bit set series
#Wall mounty bit set tv

If you're somewhat handy and have done some home improvement projects in the past, you're the perfect candidate to try a DIY TV mounting. Walmart works with both HelloTech and Angi to provide TV mounting, with prices starting at $80.Have you been thinking about mounting your TV on the wall, but put it off because you weren't really sure what was involved? Even though you know that mounting your TV will save some space, look better, and provide a more comfortable viewing experience, you may be hesitant to tackle this project. You pay extra for masking the wires or hiding them in the wall. Target works with a company called HelloTech, and charges $100 to mount your TV, connect any necessary A/V devices or peripherals, and neatly dress your wires. There’s a $100 surcharge for mounting a set on brick, stone, or plaster wall, or if you want the TV mounted above a fireplace. They’ll also make sure all the wires and cables are neatly dressed. For example, Best Buy’s Geek Squad charges $200 for a basic installation, which includes mounting the TV (on a drywalled wall), connecting a few devices, and programming your remote. Prices vary, depending on how complicated the installation will be. Retailers, including Best Buy, Target, and Walmart all offer installation services. If you’re handy, it’s really not too hard to wall-mount a TV, but not everyone has the DIY skills, or inclination, to take on the job. Measure out 3/4 of an inch to find the center of the studs, and then use 16-inch increments to find the other studs nearest the TV’s mounting location. You can also look for a light switch or power outlet, since these are mounted on the side of a stud.

#Wall mounty bit set plus

Then, use an upright straightedge or yardstick, plus a vertical level, to mark a location higher on the wall. You might be able to find these small holes by feeling for dimples-though they may be spackled and painted-or by running a magnet across the surface to locate the nails.

Wall trim or baseboards are usually nailed to the studs. Sheetrock is usually attached to studs using either screws or nails, so using a strong magnet to find a screw or nail head should put you near the center of that stud. Start at a corner of a room and then measure along the wall in 16-inch increments to locate the most likely location of the studs for your installation.

#Wall mounty bit set series

(With any of these, confirm the position of each stud by drilling a series of small holes to locate the edges of the studs.) Most walls are constructed with the studs installed with the center of each 16 inches away from the next one. If you don’t have a stud finder, there are a few other carpenter’s tricks to locating a wall stud. For the most secure attachment, the bolt should be firmly centered in any stud you are using. Next, move on to the start and end of the next stud, marking the positions as you move along. Then move it horizontally at the same height to locate the end of the first stud. When it does, mark that with a pencil or some painter’s tape so you remember the position. Move your stud finder across the wall at the height you will be installing the TV mount until it indicates it has found the edge of a stud. The easiest way to do this is by using a stud finder. You’ll want to screw the TV mount into wall studs (or into masonry using the appropriate anchors) for the most secure installation. You should make sure the location gives you easy access to an electrical outlet for power, and that you’ll have adequate storage for any components, such as a cable box, streaming player, or game console, you’ll be connecting to the TV.

#Wall mounty bit set install

If you need to install the TV higher, you’ll want to consider a tilting or articulating mount (see below). Instead, try to hang the TV so the bottom of the screen is no higher than eye level when you’re seated, and the top of the screen no higher than eye-level when you’re standing. But a wall-mounted TV tends to look weird when installed that low. If you were placing your TV on a stand, you’d want the center of the screen to be at eye level when you were seated.

The height of the screen, and the angle from the screen to where you’ll be sitting, affects picture quality.

Installing a TV on brick, block, or plaster walls generally requires special tools and hardware if it’s not included with the mount. You’ll want to attach the mount to framing studs-and not just drywall-to make sure it will support the weight of the TV. You can try a few different positions using painter’s tape to mark off the TV’s dimensions on the wall. Decide where you want to hang your TV before you go shopping for a mount, because that will affect the type of hardware you choose.